77 lines
3.9 KiB
C
77 lines
3.9 KiB
C
|
/**
|
||
|
|
@Generated PIC10 / PIC12 / PIC16 / PIC18 MCUs Source File
|
||
|
|
|
||
|
|
@Company:
|
||
|
|
Microchip Technology Inc.
|
||
|
|
|
||
|
|
@File Name:
|
||
|
|
mcc.c
|
||
|
|
|
||
|
|
@Summary:
|
||
|
|
This is the device_config.c file generated using PIC10 / PIC12 / PIC16 / PIC18 MCUs
|
||
|
|
|
||
|
|
@Description:
|
||
|
|
This header file provides implementations for driver APIs for all modules selected in the GUI.
|
||
|
|
Generation Information :
|
||
|
|
Product Revision : PIC10 / PIC12 / PIC16 / PIC18 MCUs - 1.81.8
|
||
|
|
Device : PIC18F97J60
|
||
|
|
Driver Version : 2.00
|
||
|
|
The generated drivers are tested against the following:
|
||
|
|
Compiler : XC8 2.36 and above or later
|
||
|
|
MPLAB : MPLAB X 6.00
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
(c) 2018 Microchip Technology Inc. and its subsidiaries.
|
||
|
|
|
||
|
|
Subject to your compliance with these terms, you may use Microchip software and any
|
||
|
|
derivatives exclusively with Microchip products. It is your responsibility to comply with third party
|
||
|
|
license terms applicable to your use of third party software (including open source software) that
|
||
|
|
may accompany Microchip software.
|
||
|
|
|
||
|
|
THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, WHETHER
|
||
|
|
EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, INCLUDING ANY
|
||
|
|
IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS
|
||
|
|
FOR A PARTICULAR PURPOSE.
|
||
|
|
|
||
|
|
IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE,
|
||
|
|
INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND
|
||
|
|
WHATSOEVER RELATED TO THE SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP
|
||
|
|
HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO
|
||
|
|
THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL
|
||
|
|
CLAIMS IN ANY WAY RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT
|
||
|
|
OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS
|
||
|
|
SOFTWARE.
|
||
|
|
*/
|
||
|
|
|
||
|
|
// Configuration bits: selected in the GUI
|
||
|
|
|
||
|
|
// CONFIG1L
|
||
|
|
#pragma config WDT = OFF // Watchdog Timer Enable bit->WDT disabled (control is placed on SWDTEN bit)
|
||
|
|
#pragma config STVR = ON // Stack Overflow/Underflow Reset Enable bit->Reset on stack overflow/underflow enabled
|
||
|
|
#pragma config XINST = OFF // Extended Instruction Set Enable bit->Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
|
||
|
|
#pragma config DEBUG = OFF // Background Debugger Enable bit->Background debugger disabled; RB6 and RB7 configured as general purpose I/O pins
|
||
|
|
|
||
|
|
// CONFIG1H
|
||
|
|
#pragma config CP0 = OFF // Code Protection bit->Program memory is not code-protected
|
||
|
|
|
||
|
|
// CONFIG2L
|
||
|
|
#pragma config FOSC = HS // Oscillator Selection bits->HS oscillator
|
||
|
|
#pragma config FOSC2 = ON // Default/Reset System Clock Select bit->Clock selected by FOSC1:FOSC0 as system clock is enabled when OSCCON<1:0> = 00
|
||
|
|
#pragma config FCMEN = ON // Fail-Safe Clock Monitor Enable->Fail-Safe Clock Monitor enabled
|
||
|
|
#pragma config IESO = ON // Two-Speed Start-up (Internal/External Oscillator Switchover) Control bit->Two-Speed Start-up enabled
|
||
|
|
|
||
|
|
// CONFIG2H
|
||
|
|
#pragma config WDTPS = 32768 // Watchdog Timer Postscaler Select bits->1:32768
|
||
|
|
|
||
|
|
// CONFIG3L
|
||
|
|
#pragma config EASHFT = ON // External Address Bus Shift Enable bit->Address shifting enabled; address on external bus is offset to start at 000000h
|
||
|
|
#pragma config MODE = MM // External Memory Bus->Microcontroller mode, external bus disabled
|
||
|
|
#pragma config BW = 16 // Data Bus Width Select bit->16-Bit Data Width mode
|
||
|
|
#pragma config WAIT = OFF // External Bus Wait Enable bit->Wait states for operations on external memory bus disabled
|
||
|
|
|
||
|
|
// CONFIG3H
|
||
|
|
#pragma config CCP2MX = ON // ECCP2 MUX bit->ECCP2/P2A is multiplexed with RC1
|
||
|
|
#pragma config ECCPMX = ON // ECCP MUX bit->ECCP1 outputs (P1B/P1C) are multiplexed with RE6 and RE5; ECCP3 outputs (P3B/P3C) are multiplexed with RE4 and RE3
|
||
|
|
#pragma config ETHLED = ON // Ethernet LED Enable bit->RA0/RA1 are multiplexed with LEDA/LEDB when Ethernet module is enabled and function as I/O when Ethernet is disabled
|