SummerSchool2-Controller/306-controller_interface.X/mcc_generated_files/pin_manager.h

/**
  @Generated Pin Manager Header File

  @Company:
    Microchip Technology Inc.

  @File Name:
    pin_manager.h

  @Summary:
    This is the Pin Manager file generated using PIC10 / PIC12 / PIC16 / PIC18 MCUs

  @Description
    This header file provides APIs for driver for .
    Generation Information :
        Product Revision  :  PIC10 / PIC12 / PIC16 / PIC18 MCUs - 1.81.8
        Device            :  PIC18F25K83
        Driver Version    :  2.11
    The generated drivers are tested against the following:
        Compiler          :  XC8 2.36 and above
        MPLAB 	          :  MPLAB X 6.00	
*/

/*
    (c) 2018 Microchip Technology Inc. and its subsidiaries. 
    
    Subject to your compliance with these terms, you may use Microchip software and any 
    derivatives exclusively with Microchip products. It is your responsibility to comply with third party 
    license terms applicable to your use of third party software (including open source software) that 
    may accompany Microchip software.
    
    THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, WHETHER 
    EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, INCLUDING ANY 
    IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS 
    FOR A PARTICULAR PURPOSE.
    
    IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, 
    INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND 
    WHATSOEVER RELATED TO THE SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP 
    HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO 
    THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL 
    CLAIMS IN ANY WAY RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT 
    OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS 
    SOFTWARE.
*/

#ifndef PIN_MANAGER_H
#define PIN_MANAGER_H

/**
  Section: Included Files
*/

#include <xc.h>

#define INPUT   1
#define OUTPUT  0

#define HIGH    1
#define LOW     0

#define ANALOG      1
#define DIGITAL     0

#define PULL_UP_ENABLED      1
#define PULL_UP_DISABLED     0

// get/set OUTPUT1 aliases
#define OUTPUT1_TRIS                 TRISAbits.TRISA0
#define OUTPUT1_LAT                  LATAbits.LATA0
#define OUTPUT1_PORT                 PORTAbits.RA0
#define OUTPUT1_WPU                  WPUAbits.WPUA0
#define OUTPUT1_OD                   ODCONAbits.ODCA0
#define OUTPUT1_ANS                  ANSELAbits.ANSELA0
#define OUTPUT1_SetHigh()            do { LATAbits.LATA0 = 1; } while(0)
#define OUTPUT1_SetLow()             do { LATAbits.LATA0 = 0; } while(0)
#define OUTPUT1_Toggle()             do { LATAbits.LATA0 = ~LATAbits.LATA0; } while(0)
#define OUTPUT1_GetValue()           PORTAbits.RA0
#define OUTPUT1_SetDigitalInput()    do { TRISAbits.TRISA0 = 1; } while(0)
#define OUTPUT1_SetDigitalOutput()   do { TRISAbits.TRISA0 = 0; } while(0)
#define OUTPUT1_SetPullup()          do { WPUAbits.WPUA0 = 1; } while(0)
#define OUTPUT1_ResetPullup()        do { WPUAbits.WPUA0 = 0; } while(0)
#define OUTPUT1_SetPushPull()        do { ODCONAbits.ODCA0 = 0; } while(0)
#define OUTPUT1_SetOpenDrain()       do { ODCONAbits.ODCA0 = 1; } while(0)
#define OUTPUT1_SetAnalogMode()      do { ANSELAbits.ANSELA0 = 1; } while(0)
#define OUTPUT1_SetDigitalMode()     do { ANSELAbits.ANSELA0 = 0; } while(0)

// get/set OUTPUT2 aliases
#define OUTPUT2_TRIS                 TRISAbits.TRISA1
#define OUTPUT2_LAT                  LATAbits.LATA1
#define OUTPUT2_PORT                 PORTAbits.RA1
#define OUTPUT2_WPU                  WPUAbits.WPUA1
#define OUTPUT2_OD                   ODCONAbits.ODCA1
#define OUTPUT2_ANS                  ANSELAbits.ANSELA1
#define OUTPUT2_SetHigh()            do { LATAbits.LATA1 = 1; } while(0)
#define OUTPUT2_SetLow()             do { LATAbits.LATA1 = 0; } while(0)
#define OUTPUT2_Toggle()             do { LATAbits.LATA1 = ~LATAbits.LATA1; } while(0)
#define OUTPUT2_GetValue()           PORTAbits.RA1
#define OUTPUT2_SetDigitalInput()    do { TRISAbits.TRISA1 = 1; } while(0)
#define OUTPUT2_SetDigitalOutput()   do { TRISAbits.TRISA1 = 0; } while(0)
#define OUTPUT2_SetPullup()          do { WPUAbits.WPUA1 = 1; } while(0)
#define OUTPUT2_ResetPullup()        do { WPUAbits.WPUA1 = 0; } while(0)
#define OUTPUT2_SetPushPull()        do { ODCONAbits.ODCA1 = 0; } while(0)
#define OUTPUT2_SetOpenDrain()       do { ODCONAbits.ODCA1 = 1; } while(0)
#define OUTPUT2_SetAnalogMode()      do { ANSELAbits.ANSELA1 = 1; } while(0)
#define OUTPUT2_SetDigitalMode()     do { ANSELAbits.ANSELA1 = 0; } while(0)

// get/set OUTPUT3 aliases
#define OUTPUT3_TRIS                 TRISAbits.TRISA2
#define OUTPUT3_LAT                  LATAbits.LATA2
#define OUTPUT3_PORT                 PORTAbits.RA2
#define OUTPUT3_WPU                  WPUAbits.WPUA2
#define OUTPUT3_OD                   ODCONAbits.ODCA2
#define OUTPUT3_ANS                  ANSELAbits.ANSELA2
#define OUTPUT3_SetHigh()            do { LATAbits.LATA2 = 1; } while(0)
#define OUTPUT3_SetLow()             do { LATAbits.LATA2 = 0; } while(0)
#define OUTPUT3_Toggle()             do { LATAbits.LATA2 = ~LATAbits.LATA2; } while(0)
#define OUTPUT3_GetValue()           PORTAbits.RA2
#define OUTPUT3_SetDigitalInput()    do { TRISAbits.TRISA2 = 1; } while(0)
#define OUTPUT3_SetDigitalOutput()   do { TRISAbits.TRISA2 = 0; } while(0)
#define OUTPUT3_SetPullup()          do { WPUAbits.WPUA2 = 1; } while(0)
#define OUTPUT3_ResetPullup()        do { WPUAbits.WPUA2 = 0; } while(0)
#define OUTPUT3_SetPushPull()        do { ODCONAbits.ODCA2 = 0; } while(0)
#define OUTPUT3_SetOpenDrain()       do { ODCONAbits.ODCA2 = 1; } while(0)
#define OUTPUT3_SetAnalogMode()      do { ANSELAbits.ANSELA2 = 1; } while(0)
#define OUTPUT3_SetDigitalMode()     do { ANSELAbits.ANSELA2 = 0; } while(0)

// get/set OUTPUT4 aliases
#define OUTPUT4_TRIS                 TRISAbits.TRISA3
#define OUTPUT4_LAT                  LATAbits.LATA3
#define OUTPUT4_PORT                 PORTAbits.RA3
#define OUTPUT4_WPU                  WPUAbits.WPUA3
#define OUTPUT4_OD                   ODCONAbits.ODCA3
#define OUTPUT4_ANS                  ANSELAbits.ANSELA3
#define OUTPUT4_SetHigh()            do { LATAbits.LATA3 = 1; } while(0)
#define OUTPUT4_SetLow()             do { LATAbits.LATA3 = 0; } while(0)
#define OUTPUT4_Toggle()             do { LATAbits.LATA3 = ~LATAbits.LATA3; } while(0)
#define OUTPUT4_GetValue()           PORTAbits.RA3
#define OUTPUT4_SetDigitalInput()    do { TRISAbits.TRISA3 = 1; } while(0)
#define OUTPUT4_SetDigitalOutput()   do { TRISAbits.TRISA3 = 0; } while(0)
#define OUTPUT4_SetPullup()          do { WPUAbits.WPUA3 = 1; } while(0)
#define OUTPUT4_ResetPullup()        do { WPUAbits.WPUA3 = 0; } while(0)
#define OUTPUT4_SetPushPull()        do { ODCONAbits.ODCA3 = 0; } while(0)
#define OUTPUT4_SetOpenDrain()       do { ODCONAbits.ODCA3 = 1; } while(0)
#define OUTPUT4_SetAnalogMode()      do { ANSELAbits.ANSELA3 = 1; } while(0)
#define OUTPUT4_SetDigitalMode()     do { ANSELAbits.ANSELA3 = 0; } while(0)

// get/set OUTPUT5 aliases
#define OUTPUT5_TRIS                 TRISAbits.TRISA4
#define OUTPUT5_LAT                  LATAbits.LATA4
#define OUTPUT5_PORT                 PORTAbits.RA4
#define OUTPUT5_WPU                  WPUAbits.WPUA4
#define OUTPUT5_OD                   ODCONAbits.ODCA4
#define OUTPUT5_ANS                  ANSELAbits.ANSELA4
#define OUTPUT5_SetHigh()            do { LATAbits.LATA4 = 1; } while(0)
#define OUTPUT5_SetLow()             do { LATAbits.LATA4 = 0; } while(0)
#define OUTPUT5_Toggle()             do { LATAbits.LATA4 = ~LATAbits.LATA4; } while(0)
#define OUTPUT5_GetValue()           PORTAbits.RA4
#define OUTPUT5_SetDigitalInput()    do { TRISAbits.TRISA4 = 1; } while(0)
#define OUTPUT5_SetDigitalOutput()   do { TRISAbits.TRISA4 = 0; } while(0)
#define OUTPUT5_SetPullup()          do { WPUAbits.WPUA4 = 1; } while(0)
#define OUTPUT5_ResetPullup()        do { WPUAbits.WPUA4 = 0; } while(0)
#define OUTPUT5_SetPushPull()        do { ODCONAbits.ODCA4 = 0; } while(0)
#define OUTPUT5_SetOpenDrain()       do { ODCONAbits.ODCA4 = 1; } while(0)
#define OUTPUT5_SetAnalogMode()      do { ANSELAbits.ANSELA4 = 1; } while(0)
#define OUTPUT5_SetDigitalMode()     do { ANSELAbits.ANSELA4 = 0; } while(0)

// get/set OUTPUT6 aliases
#define OUTPUT6_TRIS                 TRISAbits.TRISA5
#define OUTPUT6_LAT                  LATAbits.LATA5
#define OUTPUT6_PORT                 PORTAbits.RA5
#define OUTPUT6_WPU                  WPUAbits.WPUA5
#define OUTPUT6_OD                   ODCONAbits.ODCA5
#define OUTPUT6_ANS                  ANSELAbits.ANSELA5
#define OUTPUT6_SetHigh()            do { LATAbits.LATA5 = 1; } while(0)
#define OUTPUT6_SetLow()             do { LATAbits.LATA5 = 0; } while(0)
#define OUTPUT6_Toggle()             do { LATAbits.LATA5 = ~LATAbits.LATA5; } while(0)
#define OUTPUT6_GetValue()           PORTAbits.RA5
#define OUTPUT6_SetDigitalInput()    do { TRISAbits.TRISA5 = 1; } while(0)
#define OUTPUT6_SetDigitalOutput()   do { TRISAbits.TRISA5 = 0; } while(0)
#define OUTPUT6_SetPullup()          do { WPUAbits.WPUA5 = 1; } while(0)
#define OUTPUT6_ResetPullup()        do { WPUAbits.WPUA5 = 0; } while(0)
#define OUTPUT6_SetPushPull()        do { ODCONAbits.ODCA5 = 0; } while(0)
#define OUTPUT6_SetOpenDrain()       do { ODCONAbits.ODCA5 = 1; } while(0)
#define OUTPUT6_SetAnalogMode()      do { ANSELAbits.ANSELA5 = 1; } while(0)
#define OUTPUT6_SetDigitalMode()     do { ANSELAbits.ANSELA5 = 0; } while(0)

// get/set OUTPUT7 aliases
#define OUTPUT7_TRIS                 TRISAbits.TRISA6
#define OUTPUT7_LAT                  LATAbits.LATA6
#define OUTPUT7_PORT                 PORTAbits.RA6
#define OUTPUT7_WPU                  WPUAbits.WPUA6
#define OUTPUT7_OD                   ODCONAbits.ODCA6
#define OUTPUT7_ANS                  ANSELAbits.ANSELA6
#define OUTPUT7_SetHigh()            do { LATAbits.LATA6 = 1; } while(0)
#define OUTPUT7_SetLow()             do { LATAbits.LATA6 = 0; } while(0)
#define OUTPUT7_Toggle()             do { LATAbits.LATA6 = ~LATAbits.LATA6; } while(0)
#define OUTPUT7_GetValue()           PORTAbits.RA6
#define OUTPUT7_SetDigitalInput()    do { TRISAbits.TRISA6 = 1; } while(0)
#define OUTPUT7_SetDigitalOutput()   do { TRISAbits.TRISA6 = 0; } while(0)
#define OUTPUT7_SetPullup()          do { WPUAbits.WPUA6 = 1; } while(0)
#define OUTPUT7_ResetPullup()        do { WPUAbits.WPUA6 = 0; } while(0)
#define OUTPUT7_SetPushPull()        do { ODCONAbits.ODCA6 = 0; } while(0)
#define OUTPUT7_SetOpenDrain()       do { ODCONAbits.ODCA6 = 1; } while(0)
#define OUTPUT7_SetAnalogMode()      do { ANSELAbits.ANSELA6 = 1; } while(0)
#define OUTPUT7_SetDigitalMode()     do { ANSELAbits.ANSELA6 = 0; } while(0)

// get/set OUTPUT8 aliases
#define OUTPUT8_TRIS                 TRISAbits.TRISA7
#define OUTPUT8_LAT                  LATAbits.LATA7
#define OUTPUT8_PORT                 PORTAbits.RA7
#define OUTPUT8_WPU                  WPUAbits.WPUA7
#define OUTPUT8_OD                   ODCONAbits.ODCA7
#define OUTPUT8_ANS                  ANSELAbits.ANSELA7
#define OUTPUT8_SetHigh()            do { LATAbits.LATA7 = 1; } while(0)
#define OUTPUT8_SetLow()             do { LATAbits.LATA7 = 0; } while(0)
#define OUTPUT8_Toggle()             do { LATAbits.LATA7 = ~LATAbits.LATA7; } while(0)
#define OUTPUT8_GetValue()           PORTAbits.RA7
#define OUTPUT8_SetDigitalInput()    do { TRISAbits.TRISA7 = 1; } while(0)
#define OUTPUT8_SetDigitalOutput()   do { TRISAbits.TRISA7 = 0; } while(0)
#define OUTPUT8_SetPullup()          do { WPUAbits.WPUA7 = 1; } while(0)
#define OUTPUT8_ResetPullup()        do { WPUAbits.WPUA7 = 0; } while(0)
#define OUTPUT8_SetPushPull()        do { ODCONAbits.ODCA7 = 0; } while(0)
#define OUTPUT8_SetOpenDrain()       do { ODCONAbits.ODCA7 = 1; } while(0)
#define OUTPUT8_SetAnalogMode()      do { ANSELAbits.ANSELA7 = 1; } while(0)
#define OUTPUT8_SetDigitalMode()     do { ANSELAbits.ANSELA7 = 0; } while(0)

// get/set RB3 procedures
#define RB3_SetHigh()            do { LATBbits.LATB3 = 1; } while(0)
#define RB3_SetLow()             do { LATBbits.LATB3 = 0; } while(0)
#define RB3_Toggle()             do { LATBbits.LATB3 = ~LATBbits.LATB3; } while(0)
#define RB3_GetValue()              PORTBbits.RB3
#define RB3_SetDigitalInput()    do { TRISBbits.TRISB3 = 1; } while(0)
#define RB3_SetDigitalOutput()   do { TRISBbits.TRISB3 = 0; } while(0)
#define RB3_SetPullup()             do { WPUBbits.WPUB3 = 1; } while(0)
#define RB3_ResetPullup()           do { WPUBbits.WPUB3 = 0; } while(0)
#define RB3_SetAnalogMode()         do { ANSELBbits.ANSELB3 = 1; } while(0)
#define RB3_SetDigitalMode()        do { ANSELBbits.ANSELB3 = 0; } while(0)

// get/set RB4 procedures
#define RB4_SetHigh()            do { LATBbits.LATB4 = 1; } while(0)
#define RB4_SetLow()             do { LATBbits.LATB4 = 0; } while(0)
#define RB4_Toggle()             do { LATBbits.LATB4 = ~LATBbits.LATB4; } while(0)
#define RB4_GetValue()              PORTBbits.RB4
#define RB4_SetDigitalInput()    do { TRISBbits.TRISB4 = 1; } while(0)
#define RB4_SetDigitalOutput()   do { TRISBbits.TRISB4 = 0; } while(0)
#define RB4_SetPullup()             do { WPUBbits.WPUB4 = 1; } while(0)
#define RB4_ResetPullup()           do { WPUBbits.WPUB4 = 0; } while(0)
#define RB4_SetAnalogMode()         do { ANSELBbits.ANSELB4 = 1; } while(0)
#define RB4_SetDigitalMode()        do { ANSELBbits.ANSELB4 = 0; } while(0)

/**
   @Param
    none
   @Returns
    none
   @Description
    GPIO and peripheral I/O initialization
   @Example
    PIN_MANAGER_Initialize();
 */
void PIN_MANAGER_Initialize (void);

/**
 * @Param
    none
 * @Returns
    none
 * @Description
    Interrupt on Change Handling routine
 * @Example
    PIN_MANAGER_IOC();
 */
void PIN_MANAGER_IOC(void);



#endif // PIN_MANAGER_H
/**
 End of File
*/