feat: added PicoW_Sensor code template

Credits to @ext-erich.styger that provided the template

TSM_PicoW_Sensor/McuLib/config/McuOneWireconfig.h

@@ -0,0 +1,67 @@
+/**
+ * \file
+ * \brief Configuration header file for 1-Wire.
+ * Copyright (c) 2020, Erich Styger
+ * SPDX-License-Identifier: BSD-3-Clause
+ *
+ * This header file is used to configure settings of the 1-Wire module.
+ */
+
+#ifndef __McuOneWire_CONFIG_H
+#define __McuOneWire_CONFIG_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* protocol timing in micro seconds */
+/* write */
+#define McuOneWire_CONFIG_A_WRITE_1_LOW_TIME                6        /* A: standard 6 us, low time to write one bit */
+#define McuOneWire_CONFIG_B_WRITE_1_HIGH_TIME               64       /* B: standard 64 us, high time after writing one bit (A) */
+#define McuOneWire_CONFIG_C_WRITE_0_LOW_TIME                60       /* C: standard 60 us, Low time writing zero bit */
+#define McuOneWire_CONFIG_D_WRITE_0_HIGH_TIME               10       /* D: standard 10 us, High time after writing zero bit (C) */
+/* read */
+#define McuOneWire_CONFIG_A_READ_LOW_TIME                   6 /* Low time to start read */
+#define McuOneWire_CONFIG_E_BEFORE_READ_DELAY_TIME          3        /* E: standard 9 us, wait time after starting read (when to read bit) */
+#define McuOneWire_CONFIG_F_AFTER_READ_DELAY_TIME           55       /* F: standard 55 us, wait time after reading bit (E)  */
+/* reset */
+#define McuOneWire_CONFIG_H_RESET_TIME                      480      /* H: standard 480 us, reset low time */
+#define McuOneWire_CONFIG_I_RESET_RESPONSE_TIME             70       /* I: standard 70 us, wait time after reset low time (H) until read response */
+#define McuOneWire_CONFIG_J_RESET_WAIT_TIME                 410      /* J: standard 410 us, wait time after reading presence (I)  */
+
+#define McuOneWire_CONFIG_SLOT_TIME                         100
+
+#define McuOneWire_CONFIG_DEBUG_READ_PIN_ENABLED            (1)
+  /*!< 1: Toggle extra GPIO pin during 1-wire read access; 0: no debug */
+
+#if McuOneWire_CONFIG_DEBUG_READ_PIN_ENABLED
+  #include "DbgRd1.h" /* SDK and API used */
+  #define McuOneWire_CONFIG_DEBUG_READ_PIN_INIT             DbgRd1_Init()
+  #define McuOneWire_CONFIG_DEBUG_READ_PIN_DEINIT           DbgRd1_Deinit()
+  #define McuOneWire_CONFIG_DEBUG_READ_PIN_TOGGLE           DbgRd1_NegVal()
+#endif
+
+#ifndef McuOneWire_CONFIG_WRITE_PIN
+  #define McuOneWire_CONFIG_WRITE_PIN                       (0)
+    /*!< 1: using dedicated write pin; 0: using single pin for read/write */
+#endif
+
+#if McuOneWire_CONFIG_WRITE_PIN
+  #include "WritePin.h"
+  #define McuOneWire_CONFIG_WRITE_PIN_INIT                  WritePin_Init()
+  #define McuOneWire_CONFIG_WRITE_PIN_DEINIT                WritePin_Deinit()
+  #define McuOneWire_CONFIG_WRITE_PIN_LOW                   WritePin_ClrVal()
+  #define McuOneWire_CONFIG_WRITE_PIN_HIGH                  WritePin_SetVal()
+  #define McuOneWire_CONFIG_WRITE_PIN_SET_OUTPUT            WritePin_SetOutput()
+#endif
+
+#if !defined(McuOneWire_CONFIG_PARSE_COMMAND_ENABLED)
+  #define McuOneWire_CONFIG_PARSE_COMMAND_ENABLED          (1)
+    /*!< 1: shell support enabled, 0: otherwise */
+#endif
+
+#ifdef __cplusplus
+}  /* extern "C" */
+#endif
+
+#endif /* __McuOneWire_CONFIG_H */