doc/examples.typ

@@ -79,6 +79,81 @@ wire.stub("p", "south", name: "south", length: 15pt)
 wire.stub("p", "west", name: "west", length: 3em)
 ```)
 
+#let breakout = example(```
+// 16 breakouts: 4 directions × 4 label positions, laid out
+// two per row so the labels have room to breathe.
+let dirs = ("north-east", "north-west", "south-east", "south-west")
+let poss = ("north-east", "north-west", "south-east", "south-west")
+let short = (
+  "north-east": "NE", "north-west": "NW",
+  "south-east": "SE", "south-west": "SW",
+)
+let cols = 2
+let dx = 5
+let dy = 2
+for (i, dir) in dirs.enumerate() {
+  for (j, pos) in poss.enumerate() {
+    let n = i * poss.len() + j
+    let r = calc.floor(n / cols)
+    let c = calc.rem(n, cols)
+    draw.circle((c * dx, -r * dy), radius: .05)
+    wire.breakout("b" + str(n),
+      x: c * dx, y: -r * dy,
+      direction: dir,
+      port-side: if dir.ends-with("east") { "west" } else { "east" },
+      name: short.at(dir) + "/" + short.at(pos),
+      name-pos: pos)
+  }
+}
+```)
+
+#let breakout-label = example(```
+// name-pos matches direction → label sits at the end point.
+wire.breakout("b1", x: 0, y: 0, direction: "north-east",
+              port-side: "east",
+              name: "at end", name-pos: "north-east")
+
+// name-pos opposite to direction → label would cover the line, so
+// it falls back to the start point.
+wire.breakout("b2", x: 4, y: 0, direction: "north-east",
+              port-side: "east",
+              name: "at start", name-pos: "south-west")
+```, vertical: true)
+
+#let breakout-wire = example(```
+// Bus fan-out: a horizontal wire from the left block to the lower
+// right block carries the full 10-bit bus. A breakout in the middle
+// of that wire taps bits [9:5] and routes them to the upper right
+// block via an L-shaped zigzag (up, then right).
+element.block(x: 0, y: 0, w: 2, h: 2, id: "src",
+  fill: util.colors.blue,
+  ports: (east: ((id: "out"),)))
+element.block(x: 6, y: 0, w: 2, h: 2, id: "dstL",
+  fill: util.colors.green,
+  ports: (west: ((id: "in"),)))
+element.block(x: 6, y: 4, w: 2, h: 2, id: "dstU",
+  fill: util.colors.orange,
+  ports: (west: ((id: "in"),)))
+
+// Full bus wire, labelled "[9:0]" on the left.
+wire.wire("wbus", ("src-port-out", "dstL-port-in"),
+          name: "[9:0]", name-pos: "start")
+
+// Breakout tapped from the midpoint of the bus.
+wire.breakout("tap",
+  x: (rel: 2, to: "src-port-out"),
+  y: (from: "src-port-out"),
+  direction: "north-east",
+  port-side: "west",
+  name: "[9:5]", name-pos: "north-east")
+
+// L-shaped wire from the breakout up and then right to the upper
+// block's input.
+wire.wire("wtap", ("tap-port-tap", "dstU-port-in"),
+          style: "zigzag", zigzag-dir: "horizontal",
+          zigzag-ratio: 100%)
+```)
+
 #let gate-and = example(```
 gates.gate-and(x: 0, y: 0, w: 1.5, h: 1.5)
 gates.gate-and(x: 3, y: 0, w: 1.5, h: 1.5, inverted: "all")

gallery/test_breakout.typ

@@ -0,0 +1,117 @@
+// Demonstrates the wire.breakout element used to split off slices of a
+// bus that connects blocks. The main bus wires are always laid out
+// orthogonally; breakouts diagonally tap intermediate points on those
+// wires and route the sub-bus to another block via an L-shaped zigzag.
+#import "/src/lib.typ": circuit, element, util, wire
+
+#set page(width: auto, height: auto, margin: .5cm)
+
+#circuit({
+  // ---- Source block on the left, main sink on the right ----
+  element.block(x: 0, y: 0, w: 2, h: 2, id: "src", fill: util.colors.blue, ports: (
+    east: ((id: "out"),),
+  ))
+
+  element.block(x: 15, y: 0, w: 2, h: 2, id: "dstMain", fill: util.colors.green, ports: (
+    west: ((id: "in"),),
+  ))
+
+  // Full bus from src to dstMain, labelled [15:0] at the start.
+  wire.wire("wbus", ("src-port-out", "dstMain-port-in"), name: "[15:0]", name-pos: "start")
+
+  // ---- Upper-left sink: taps bits [11:8] via NW breakout ----
+  element.block(x: 0, y: 4, w: 2, h: 2, id: "dstNW", fill: util.colors.yellow, ports: (
+    east: ((id: "in"),),
+  ))
+
+  wire.breakout(
+    "tapNE",
+    x: (rel: 3, to: "src-port-out"),
+    y: (from: "src-port-out"),
+    direction: "north-east",
+    port-side: "west",
+    name: "[15:12]",
+    name-pos: "north-east",
+  )
+
+  // L-shape: up first, then left into dstNW.
+  wire.wire(
+    "wNW",
+    ("tapNE-port-tapNE", "dstNW-port-in"),
+    style: "zigzag",
+    zigzag-dir: "horizontal",
+    zigzag-ratio: 100%,
+  )
+
+  // ---- Upper-right sink: taps bits [15:12] via NE breakout ----
+  element.block(x: 15, y: 4, w: 2, h: 2, id: "dstNE", fill: util.colors.orange, ports: (
+    west: ((id: "in"),),
+  ))
+
+  wire.breakout(
+    "tapNW",
+    x: (rel: 7, to: "src-port-out"),
+    y: (from: "src-port-out"),
+    direction: "north-west",
+    port-side: "east",
+    name: "[11:8]",
+    name-pos: "north-east",
+  )
+
+  // L-shape: up first, then right into dstNE.
+  wire.wire(
+    "wNE",
+    ("tapNW-port-tapNW", "dstNE-port-in"),
+    style: "zigzag",
+    zigzag-dir: "horizontal",
+    zigzag-ratio: 100%,
+  )
+
+  // ---- Lower-left sink: taps bits [3:0] via SW breakout ----
+  element.block(x: 0, y: -4, w: 2, h: 2, id: "dstSW", fill: util.colors.purple, ports: (
+    east: ((id: "in"),),
+  ))
+
+  wire.breakout(
+    "tapSE",
+    x: (rel: 5, to: "src-port-out"),
+    y: (from: "src-port-out"),
+    direction: "south-east",
+    port-side: "west",
+    name: "[7:4]",
+    name-pos: "south-east",
+  )
+
+  // L-shape: down first, then left into dstSW.
+  wire.wire(
+    "wSW",
+    ("tapSE-port-tapSE", "dstSW-port-in"),
+    style: "zigzag",
+    zigzag-dir: "horizontal",
+    zigzag-ratio: 100%,
+  )
+
+  // ---- Lower-right sink: taps bits [7:4] via SE breakout ----
+  element.block(x: 15, y: -4, w: 2, h: 2, id: "dstSE", fill: util.colors.pink, ports: (
+    west: ((id: "in"),),
+  ))
+
+  wire.breakout(
+    "tapSW",
+    x: (rel: 11, to: "src-port-out"),
+    y: (from: "src-port-out"),
+    direction: "south-west",
+    port-side: "east",
+    name: "[3:0]",
+    name-pos: "south-west",
+  )
+
+  // L-shape: down first, then right into dstSE.
+  wire.wire(
+    "wSE",
+    ("tapSW-port-tapSW", "dstSE-port-in"),
+    style: "zigzag",
+    zigzag-dir: "horizontal",
+    zigzag-ratio: 100%,
+  )
+})

gallery/test_yrel.typ

@@ -0,0 +1,46 @@
+// Demonstrates the `(rel: <number>, to: <anchor>)` shorthand for the `y`
+// parameter (analogous to the existing shorthand for `x`).
+#import "/src/lib.typ": circuit, element, util, wire
+
+#set page(width: auto, height: auto, margin: .5cm)
+
+#circuit({
+  // Anchor block: absolute placement.
+  element.block(
+    x: 0, y: 0, w: 2, h: 1.5,
+    id: "A",
+    fill: util.colors.orange,
+    ports: (east: ((id: "out"),))
+  )
+
+  // X relative, Y absolute (existing feature).
+  element.block(
+    x: (rel: 1, to: "A.east"), y: 0, w: 2, h: 1.5,
+    id: "B",
+    fill: util.colors.yellow,
+    ports: (west: ((id: "in"),), east: ((id: "out"),))
+  )
+
+  // Both X and Y relative to another element's anchor (new feature).
+  element.block(
+    x: (rel: 1, to: "B.east"),
+    y: (rel: 2, to: "B.south-west"),
+    w: 2, h: 1.5,
+    id: "C",
+    fill: util.colors.green,
+    ports: (west: ((id: "in"),))
+  )
+
+  // Y relative only, X absolute.
+  element.block(
+    x: 0,
+    y: (rel: -2.5, to: "A.south-west"),
+    w: 2, h: 1.5,
+    id: "D",
+    fill: util.colors.blue,
+    ports: (east: ((id: "out"),))
+  )
+
+  wire.wire("wAB", ("A-port-out", "B-port-in"))
+  wire.wire("wBC", ("B-port-out", "C-port-in"), style: "zigzag")
+})

manual.typ

@@ -1,4 +1,4 @@
-#import "@preview/tidy:0.4.1"
+#import "@preview/tidy:0.4.3"
 #import "/src/cetz.typ": draw, canvas
 #import "src/lib.typ"
 #import "doc/examples.typ"

src/cetz.typ

@@ -1 +1 @@
-#import "@preview/cetz:0.3.4": *
+#import "@preview/cetz:0.5.2": *

src/circuit.typ

@@ -1,5 +1,5 @@
 #import "/src/cetz.typ": canvas
-#import "@preview/tidy:0.3.0"
+#import "@preview/tidy:0.4.3"
 
 /// Draws a block circuit diagram
 ///

src/elements/element.typ

@@ -24,7 +24,9 @@
 ///   If it is a dictionary, it should be in the format `(rel: number, to: str)`, where `rel` is the offset and `to` the base anchor
 /// - y (number, dictionary): The y position (bottom-left corner).
 ///
-///   If it is a dictionary, it should be in the format `(from: str, to: str)`, where `from` is the base anchor and `to` is the id of the port to align with the anchor
+///   If it is a dictionary, it can take one of two forms:
+///     - `(rel: number, to: str)`: `rel` is the y offset and `to` the base anchor (analogous to `x`)
+///     - `(from: str, to: str)`: `from` is the base anchor and `to` is the id of the port to align with the anchor
 /// - w (number): Width of the element
 /// - h (number): Height of the element
 /// - name (none, str): Optional name of the block
@@ -74,13 +76,12 @@
   if h == none { panic("Parameter h must be set") }
 
   if (type(x) == dictionary) {
-    let offset = x.rel
-    let to = x.to
-    let (ctx, to-pos) = coordinate.resolve(ctx, (rel: (offset, 0), to: to))
-    x = to-pos.at(0)
+    x = util.resolve-rel-coord(ctx, x, 0)
   }
   
-  if (type(y) == dictionary) {
+  if (type(y) == dictionary and "rel" in y) {
+    y = util.resolve-rel-coord(ctx, y, 1)
+  } else if (type(y) == dictionary) {
     let from = y.from
     let to = y.to
     let (to-side, i) = find-port(ports, to)

src/elements/logic/gate.typ

@@ -1,4 +1,5 @@
 #import "/src/cetz.typ": draw, coordinate
+#import "/src/util.typ"
 #import "../ports.typ": add-ports, add-port
 #import "../element.typ"
 
@@ -49,13 +50,12 @@
   if h == none { panic("Parameter h must be set") }
 
   if (type(x) == dictionary) {
-    let offset = x.rel
-    let to = x.to
-    let (ctx, to-pos) = coordinate.resolve(ctx, (rel: (offset, 0), to: to))
-    x = to-pos.at(0)
+    x = util.resolve-rel-coord(ctx, x, 0)
   }
   
-  if (type(y) == dictionary) {
+  if (type(y) == dictionary and "rel" in y) {
+    y = util.resolve-rel-coord(ctx, y, 1)
+  } else if (type(y) == dictionary) {
     let from = y.from
     let to = y.to
     

src/elements/logic/iec_gate.typ

@@ -1,4 +1,5 @@
 #import "/src/cetz.typ": draw, coordinate
+#import "/src/util.typ"
 #import "../ports.typ": add-ports, add-port
 #import "../element.typ"
 
@@ -60,13 +61,12 @@
   if h == none { panic("Parameter h must be set") }
 
   if (type(x) == dictionary) {
-    let offset = x.rel
-    let to = x.to
-    let (ctx, to-pos) = coordinate.resolve(ctx, (rel: (offset, 0), to: to))
-    x = to-pos.at(0)
+    x = util.resolve-rel-coord(ctx, x, 0)
   }
   
-  if (type(y) == dictionary) {
+  if (type(y) == dictionary and "rel" in y) {
+    y = util.resolve-rel-coord(ctx, y, 1)
+  } else if (type(y) == dictionary) {
     let from = y.from
     let to = y.to
     

src/util.typ

@@ -1,3 +1,23 @@
+#import "cetz.typ": coordinate
+
+/// Resolves a relative coordinate shorthand of the form `(rel: <number>, to: <anchor>)`
+/// to a single scalar along the requested axis.
+///
+/// Used to implement the shared `(rel:, to:)` shorthand accepted by the `x` and
+/// `y` parameters of `elmt`, `gate` and `iec-gate`.
+///
+/// - ctx (dictionary): The current CeTZ context
+/// - val (dictionary): A dictionary with fields `rel` (number) and `to` (anchor)
+/// - axis (int): `0` for x, `1` for y
+/// -> number
+#let resolve-rel-coord(ctx, val, axis) = {
+  let offset = val.rel
+  let to = val.to
+  let delta = if axis == 0 { (offset, 0) } else { (0, offset) }
+  let (_, to-pos) = coordinate.resolve(ctx, (rel: delta, to: to))
+  return to-pos.at(axis)
+}
+
 /// Predefined color palette
 /// #let w = 4
 /// #box(width: 100%, align(center)[
@@ -73,4 +93,45 @@
 #let valid-anchors = (
   "center", "north", "east", "west", "south",
   "north-east", "north-west", "south-east", "south-west"
-)
+)
+
+/// Normalizes a coordinate so that 2D points (x, y) are padded
+/// to (x, y, 0) as required by CeTZ's coordinate resolver.
+/// Also handles function-based and dictionary-based coordinates
+/// recursively.
+///
+/// - coord (any): A CeTZ-compatible coordinate
+/// -> any
+#let normalize-coord(coord) = {
+  if type(coord) == array {
+    if coord.len() == 2 {
+      let (a, b) = coord
+      // Raw 2D point: (x, y) -> (x, y, 0)
+      if type(a) in (int, float) and type(b) in (int, float) {
+        return (a, b, 0)
+      }
+      // Function-based coordinate: (fn, point)
+      if type(a) == function {
+        let orig = a
+        return (v => {
+          let result = orig(v)
+          if type(result) == array and result.len() == 2 {
+            let (rx, ry) = result
+            if type(rx) in (int, float) and type(ry) in (int, float) {
+              return (rx, ry, 0)
+            }
+          }
+          return result
+        }, b)
+      }
+    }
+  }
+  if type(coord) == dictionary {
+    let result = (:)
+    for (key, value) in coord {
+      result.insert(key, normalize-coord(value))
+    }
+    return result
+  }
+  return coord
+}

src/wire.typ

@@ -1,5 +1,5 @@
 #import "/src/cetz.typ": draw, coordinate
-#import "util.typ": opposite-anchor
+#import "util.typ": opposite-anchor, normalize-coord, resolve-rel-coord
 
 /// List of valid wire styles
 /// #examples.wires
@@ -68,8 +68,8 @@
   
   let (ctx, p0) = coordinate.resolve(ctx, start)
   let (ctx, p3) = coordinate.resolve(ctx, end)
-  p0 = (x: p0.first(), y: p0.last())
-  p3 = (x: p3.first(), y: p3.last())
+  p0 = (x: p0.first(), y: p0.at(1))
+  p3 = (x: p3.first(), y: p3.at(1))
 
   let dx1 = margin-start
   let dx2 = margin-end
@@ -86,13 +86,13 @@
   if side-end == "east" {
     dx2 *= -1
   }
-  p1 = (p0.x + dx1, p0.y)
-  p2 = (p3.x - dx2, p0.y)
+  p1 = (p0.x + dx1, p0.y, 0)
+  p2 = (p3.x - dx2, p0.y, 0)
 
   let points = (
     start,
     (horizontal: p1, vertical: ()),
-    (horizontal: (), vertical: (0, dodge-y)),
+    (horizontal: (), vertical: (0, dodge-y, 0)),
     (horizontal: p2, vertical: ()),
     (horizontal: (), vertical: end),
     end
@@ -147,18 +147,18 @@
 
 
   // points that are closest to the edge points
-  let p1 = (p0.x + dx1, p0.y + dy1)
-  let p5 = (p6.x + dx2, p6.y + dy2)
+  let p1 = (p0.x + dx1, p0.y + dy1, 0)
+  let p5 = (p6.x + dx2, p6.y + dy2, 0)
 
 
   // middle point
   let center_x = p0.x + box_width * center_horizontal / 100%
   let center_y = p0.y + box_height * center_vertical / 100%
-  let p3 = (center_x, center_y)
+  let p3 = (center_x, center_y, 0)
 
   // setting up the points for that touch the guides
-  let p2 = (0,0)
-  let p4 = (0,0)
+  let p2 = (0, 0, 0)
+  let p4 = (0, 0, 0)
   if side-start in ("north", "south") {
     p2 = (horizontal: p3, vertical: p1)
   } else {
@@ -240,6 +240,9 @@
   if pts.len() != 2 {
     panic("Wrong number of points (got " + str(pts.len()) + " instead of 2)")
   }
+
+  // Normalize user-provided coordinates: (x, y) -> (x, y, 0)
+  let pts = pts.map(normalize-coord)
   
   let stroke = (
     paint: color,
@@ -400,3 +403,141 @@
     )
   }
 }
+
+/// Draws a wire breakout: a 45° diagonal line starting at (x, y) and
+/// ending 1 unit away in one of the four diagonal directions. The end
+/// point exposes a port anchor named `<id>-port-<id>` so wires can attach
+/// to it as if it were a block port. A synthesized `<id>.center` anchor
+/// is placed opposite `port-side`, so the cardinal side the port faces
+/// can be deduced by comparing the port with the `.center` anchor.
+///
+/// #examples.breakout
+///
+/// Label positions are anchored so that the label sits neatly next to the
+/// end point of the breakout. When the label direction matches the
+/// breakout direction (which would overlap the line) the label is
+/// automatically placed at the start point instead so the text does not
+/// cover the line.
+///
+/// #examples.breakout-label
+///
+/// The port anchor makes it easy to fan out a bus:
+///
+/// #examples.breakout-wire
+///
+/// - id (str): The breakout id (also used as the port id)
+/// - x (number, dictionary): The starting x position (same forms as `element.block`)
+/// - y (number, dictionary): The starting y position (same forms as `element.block`)
+/// - direction (str): One of `"north-east"`, `"north-west"`, `"south-east"`, `"south-west"`
+/// - length (length, number): The diagonal length (default `1em`, matches port size)
+/// - port-side (str): Cardinal side used for wire-attach behavior (`"north"`, `"east"`, `"south"`, `"west"`)
+/// - stroke (stroke): Line stroke (paint + thickness)
+/// - name (none, str): Optional label displayed near the breakout
+/// - name-pos (none, str): Label position, one of `"north-west"`, `"north-east"`, `"south-west"`, `"south-east"`
+/// - debug (bool): If true, shows a red dot at the port anchor
+#let breakout(
+  id,
+  x: none, y: none,
+  direction: "north-east",
+  length: 1em,
+  port-side: "east",
+  stroke: black + 1pt,
+  name: none,
+  name-pos: none,
+  debug: false,
+) = draw.get-ctx(ctx => {
+  if x == none { panic("breakout: parameter x must be set") }
+  if y == none { panic("breakout: parameter y must be set") }
+
+  let valid-directions = ("north-east", "north-west", "south-east", "south-west")
+  if not direction in valid-directions {
+    panic("breakout: invalid direction '" + repr(direction)
+          + "'; must be one of " + repr(valid-directions))
+  }
+  let valid-sides = ("north", "east", "south", "west")
+  if not port-side in valid-sides {
+    panic("breakout: invalid port-side '" + repr(port-side)
+          + "'; must be one of " + repr(valid-sides))
+  }
+
+  // Diagonal component: length / sqrt(2). Resolve to a canvas-space
+  // number so we can do arithmetic with anchor coordinates.
+  let d-raw = length / calc.sqrt(2)
+  let (_, d-vec) = coordinate.resolve(ctx, (d-raw, 0, 0))
+  let d = d-vec.at(0)
+
+  // Direction sign vector for (dx, dy).
+  let sx = if direction.ends-with("east") { 1 } else { -1 }
+  let sy = if direction.starts-with("north") { 1 } else { -1 }
+
+  // Resolve x.
+  let sx0 = x
+  if type(x) == dictionary {
+    if "rel" in x {
+      sx0 = resolve-rel-coord(ctx, x, 0)
+    } else if "from" in x {
+      let (_, from-pos) = coordinate.resolve(ctx, x.from)
+      sx0 = from-pos.at(0)
+    } else {
+      panic("breakout: unsupported x dictionary: " + repr(x))
+    }
+  }
+  // Resolve y.
+  let sy0 = y
+  if type(y) == dictionary {
+    if "rel" in y {
+      sy0 = resolve-rel-coord(ctx, y, 1)
+    } else if "from" in y {
+      let (_, from-pos) = coordinate.resolve(ctx, y.from)
+      sy0 = from-pos.at(1)
+    } else {
+      panic("breakout: unsupported y dictionary: " + repr(y))
+    }
+  }
+
+  let start = (sx0, sy0)
+  let end = (rel: (sx * d, sy * d), to: start)
+
+  // Offset used for the synthesized center anchor: opposite of port-side.
+  let center-offset = (
+    "north": (0, -1em),
+    "east":  (-1em, 0),
+    "south": (0, 1em),
+    "west":  (1em, 0),
+  ).at(port-side)
+
+  let port-anchor-name = id + "-port-" + id
+
+  draw.group(name: id, {
+    draw.line(start, end, stroke: stroke)
+    draw.anchor("start", start)
+    draw.anchor("end", end)
+    draw.anchor("center", (rel: center-offset, to: end))
+
+    if name != none and name-pos != none {
+      let label-anchor = (
+        "north-west": "south-east",
+        "north-east": "south-west",
+        "south-west": "north-east",
+        "south-east": "north-west",
+      ).at(name-pos)
+
+      // Overlap case: label direction is opposite to breakout direction,
+      // so the label at the end point would extend back over the line.
+      // Anchor it at the start point instead.
+      let label-pos = if name-pos == opposite-anchor(direction) { start } else { end }
+
+      draw.content(label-pos, anchor: label-anchor, padding: 3pt, name)
+    }
+  })
+
+  // Port anchor emitted at top level so it can be referenced by its
+  // bare name (mirrors add-port's approach in ports.typ).
+  if debug {
+    draw.circle(end, name: port-anchor-name,
+                radius: .1, stroke: none, fill: red)
+  } else {
+    draw.hide(draw.circle(end, name: port-anchor-name,
+                          radius: 0, stroke: none))
+  }
+})

typst.toml

@@ -1,7 +1,7 @@
 [package]
 name = "circuiteria"
 version = "0.2.1"
-compiler = "0.13.1"
+compiler = "0.15.0"
 repository = "https://git.kb28.ch/HEL/circuiteria"
 entrypoint = "src/lib.typ"
 authors = [